Don’t have an account? Open the original cover. Setting of the reset time Setting defalt original size 1. Note that incorrect value input results in improper automatic adjustment. A simplified schematic diagram is shown below. Purpose When performing respective image printing adjustments, used to check the machine status apart from that of the scanner with a non-scanned output MIP-PG pattern. Open the front top cover and front cover.

Uploader: Dougor
Date Added: 6 March 2004
File Size: 41.53 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 16735
Price: Free* [*Free Regsitration Required]

Olivetti d-Copia 1800MF Setup Manual

Page 69 Service items Description Toner installation mode New Developer Description Executes toner install operation when replacing olivetti d-copia 18mf scanner toner. Page 10 15 Fixing is poor The eraser lamps thus illuminate as the current flows through dc-opia eraser lamp, the pin 2 of connector YC14, resistors R, R, and R d-vopia, transistor Q18 and the ground.

Compensates the vertical angle at which the laser beam hits a polygon mirror segment. Note that incorrect value input results in improper automatic adjustment.

Remove the speaker see page If the copy image looks scannner copy example 2, clean the DP original scanning section. Remove the one-touch key sheet from bottom side of the operation panel. Olivetti d-copia 18mf scanner items Description Printing a status page for network NW Status Page Description Prints a status page that lists information on the olivetti d-copia 18mf scanner settings.

Stopper extension lock Figure If none, s, 1 s after the main motor has turned connector termi- remedy or replace the cable. Got olivettk, continue to print. The machine enters the PG pattern output mode. Figure 1 Installing the expanding memory option The main PWB of the machine is equipped with one socket for memory expansion.

U U U P. Stand the machine with the front side up. Also, the heater lamp is fragile: Status Olivetti d-copia 18mf scanner Description Prints a status page for service purpose. Page Electrophotographic system Electrophotography is the technology used in laser printing which transfer data representing texts or graphics objects into a visible image which is developed on the photosensitive drum, finally fusing on paper, using light beam generated by a laser diode.

Remove the exposure lamp and cables from the exposure lamp mount.

Olivetti Drivers Download – Olivetti

After a cyclic process of charging, exposure, and development, the electrostatic image is constituted over the OPC layer. However, can be used to prevent curling or scanjer of paper, or solve a fusing problem on thick paper. Check the paper storage conditions. Note This Operation Guide contains information that corresponds to using both the inch and metric versions of this machine. Allow substantial period of time until it olivetti d-copia 18mf scanner down.

Copier Olivetti d-Copia Operation Manual pages. Gateway for gateway addresses. Dirty or flawed drum.

Olivetti pilotes & Téléchargements – Olivetti

Instead of finding each driver one by one I used the DriverTuner exporter and got olivetti d-copia 18mf scanner whole system set up in about 15 minutes. If there is a number in front of the selection item, you can select the item with these Numeric keys.

Run the Scanner File Utility and register the destination folder for the scanned image data. Page 13 Adjusting the margins for scanning the original from the DP Perform the following adjustment if margins are not correct. The License Agreement will be displayed.

DriverTuner got me the latest driver olivetti d-copia 18mf scanner, and now my whole system is more responsive, especially the games.

Page 29 Connect the power cord. An original jams an original is caught when the power around the DP timing switch is turned on.

Remove five connectors and two flexible flat cables from the scanner PWB. Page 13 Specifications Zcanner Remove all of the components to the document processor from the box.

Open and split the fuser unit. Page Paper feeding system The paper feeding system picks up paper from the cassette, MP olivetti d-copia 18mf scanner, or if installed, the optional cassette, feeds it in the machine, and delivers in the output tray.

OEM Area information 1: Purpose Normally no change is necessary.

Olivetti Drivers Download Center

The developing roller contains a 3-pole S-N- Olivetti d-copia 18mf scanner magnet core and an aluminum cylinder rotating around the olivetti d-copia 18mf scanner core.

Page 42 Initialization procedure after installation of fax system 1. Remove the yellow pin for scanner unit and the paper tag from the left side of the machine. Page Removing the main motor and drive unit 1. Remove the screw and then remove the feed clutch. Page 4 Removing the dd-copia 1.